Skip to content

Small-Scale Bioretention Systems

Small-scale bioretention systems use a shallow, vegetated depression filled with engineered soil media to capture, filter, and often infiltrate stormwater runoff. They are one of the most widely used Green Infrastructure BMPs in New Jersey.

Source: NJ Stormwater BMP Manual, Chapter 9, Section 9.7 (2026)

Bioretention manages stormwater by collecting runoff in a planted depression where it ponds briefly, then passes through an engineered media profile. Treatment occurs through physical filtration, adsorption in the media, and biological uptake by vegetation. In soils with sufficient permeability, water infiltrates to groundwater; where native soils are unsuited, an underdrain conveys filtered effluent to a receiving system.

Small-scale bioretention (Chapter 9) is distinct from large-scale bioretention (Chapter 10) in that it typically serves smaller drainage areas — up to a few acres — and is commonly deployed in residential yards, parking lot islands, roadside swales, and plazas.

Primary stormwater functions:

  • Water quality treatment — removes TSS, nutrients, metals, and hydrocarbons
  • Runoff volume reduction — through infiltration and evapotranspiration
  • Groundwater recharge — where native soils permit infiltration

When engineers choose this BMP:

Engineers select small-scale bioretention when a site has moderate drainage areas, available surface area for a shallow depression, and soils or site conditions that support infiltration or underdrain discharge. It is preferred when the project must satisfy the Green Infrastructure requirement under N.J.A.C. 7:8-5.3 and the site can accommodate a vegetated feature.

Source: NJ Stormwater BMP Manual, Chapter 9, Section 9.7 (2026)

Confirm all values against the current NJ Stormwater BMP Manual, Section 9.7, before use in design. Run Agent 1 with 2026_BMP_9_7_Small_Scale_Bioretention_Systems.pdf to generate verified content.

Parameter 2026 Requirement 2023 Requirement Notes
Contributing drainage area Typically ≤ 2–5 acres Typically ≤ 2–5 acres Verify against manual; larger areas require large-scale BMP (Ch. 10)
Maximum ponding depth 12 in 12 in No change
Typical ponding depth 6 in 6 in No change
Engineered media depth 18–48 in 18–48 in Depth depends on pollutant removal targets
Drawdown time (ponding) 48 hours maximum 48 hours maximum No change
Underdrain required when Native soil ksat < 0.5 in/hr or HSG C/D Native soil ksat < 0.5 in/hr or HSG C/D No change
Minimum SHWT separation 2 ft below bottom of media 2 ft below bottom of media See Siting Constraints tab
Pretreatment Required for drainage areas with significant sediment loads Required Forebay or filter strip typical

2026 Update: Confirm whether Chapter 14 (Volumetric Reduction Standards, new in 2026) affects sizing calculations for small-scale bioretention. Chapter 14 was not present in the 2023 manual.

Source: NJ Stormwater BMP Manual, Ch. 9, Section 9.7; Ch. 12 (Soil Testing); Ch. 13 (Groundwater Mounding)

Bioretention can be used on a wide range of sites but requires careful siting to ensure long-term performance. The following conditions limit applicability:

Seasonal High Water Table (SHWT)

  • Minimum 2 ft separation required between the bottom of the bioretention media and the SHWT
  • SHWT must be determined by field investigation (soil borings, monitoring wells) per BMP Manual Chapter 12
  • See Seasonal High Water Table

Soil Permeability

  • An underdrain is required where native soil infiltration rate is below 0.5 in/hr or where soils are HSG C or D
  • Excessively permeable soils (> 8 in/hr) may not provide adequate water quality treatment contact time — evaluate media design accordingly
  • See Soil Permeability Testing

Groundwater Mounding

  • Required where infiltration volumes are significant and the water table is shallow
  • Analysis per BMP Manual Chapter 13 (Hantush-modified or equivalent method)
  • See Groundwater Mounding

Prohibited and Restricted Locations

  • Karst geology — infiltration risk; evaluate carefully or use underdrain design
  • Contaminated sites — infiltration can mobilize contaminants; NJDEP review required
  • Areas with high salt/de-icer application — evaluate media degradation risk
  • Steep slopes (> 6–8% in contributing area) — runoff velocity may exceed inlet capacity

Source: NJ Stormwater BMP Manual, Ch. 9, Section 9.7; Ch. 12; Ch. 13

Small-scale bioretention requires regular inspection and preventive maintenance to sustain performance. Neglect is the leading cause of long-term failure.

Routine Inspection (semi-annual minimum; after major storm events)

  • Confirm ponding drains within 48 hours after storm events
  • Inspect inlet for erosion, undercutting, or blockage
  • Inspect overflow structure for debris or obstruction
  • Check pretreatment forebay for sediment accumulation

Sediment and Debris Management

  • Remove sediment from forebay or pretreatment area annually or when 50% full
  • Remove surface debris (leaves, litter) from ponding area
  • Do not allow sediment to accumulate on the media surface — it causes clogging

Vegetation Management

  • Target: ≥ 90% vegetative cover
  • Replace dead or failing plants with native species appropriate for NJ climate
  • Remove invasive species promptly
  • Avoid compaction — do not walk on or drive over the media surface
  • Mulch layer (if used) should be replenished as needed; avoid fine-textured mulch near inlets

Underdrain and Outlet

  • Inspect underdrain cleanouts annually (flush if flow is reduced)
  • Confirm outlet is functioning and not eroding the downstream area

Source: NJ Stormwater BMP Manual, Ch. 8 (Maintenance and Retrofit); Ch. 9, Section 9.7

Design Errors

  • Undersized pretreatment — sediment-laden runoff loads the media surface directly, causing rapid clogging
  • Insufficient media depth for target pollutant removal (nutrients require deeper media than TSS alone)
  • Underdrain omitted on HSG C/D soils — system drains too slowly and ponds past the 48-hour drawdown limit
  • Drainage area exceeds design capacity — peak inflow overwhelms ponding depth and causes bypass before treatment

Construction Issues

  • Media compaction during installation — heavy equipment driven over media destroys porosity; inspect and reject compacted lifts
  • Wrong soil media composition — substituting local fill or topsoil for specified engineered media destroys treatment performance
  • Inlet elevation set too low — concentrated flow scours media surface
  • SHWT not verified during construction — media placed too close to groundwater causes saturated conditions and plant mortality

Long-Term Performance Risks

  • Media surface clogging — fine sediments accumulate and progressively reduce infiltration rate; typically visible as surface ponding beyond 48 hours
  • Vegetation loss — bare media is subject to erosion and surface sealing; maintain cover per inspection schedule
  • Inlet erosion — concentrated inflow without energy dissipation scours the bioretention surface over time (Engineering inference)
  • Underdrain blockage — roots or fine sediments can block perforations; annual flushing is recommended

Governing Regulations

Rule Section Topic Engineering Relevance
N.J.A.C. 7:8-5.3 Green Infrastructure Requirement Small-scale bioretention qualifies as GI; required where feasible
N.J.A.C. 7:8-5.3(d) Water Quality Treatment Must achieve 80% TSS removal or equivalent load reduction
N.J.A.C. 7:8-5.4(a) Groundwater Recharge Recharge credit available if infiltration is confirmed feasible
N.J.A.C. 7:8-5.4(b) Stormwater Quantity Control May provide peak flow reduction credit depending on design

BMP Manual Source

  • NJ Stormwater BMP Manual, Chapter 9, Section 9.7 (2026)
  • NJ Stormwater BMP Manual, Chapter 12 — Soil Testing Criteria
  • NJ Stormwater BMP Manual, Chapter 13 — Groundwater Mounding Analysis

Related OPAL Pages